Skip to product information
1 of 12

NEP Audio

2X700W Class D Amplifier Board

Regular price $152.99 USD
Regular price $218.99 USD Sale price $152.99 USD
Sale Sold out
Shipping calculated at checkout.

We will try to keep these in stock, but many times these items are being drop shipped to our facility for inspection. We will then send the product on to you. This could delay the time it takes to receive the items by 5 days to 2 weeks. We have decided it was best to make sure it checks out OK before having it go out to you. Contact us for ETAs before or after purchase, because we always have them coming in.

Tips :

1. The rated power supply voltage is ±75V for dual power supply and ±58---±85V for voltage. (If it is a power frequency transformer, please leave a margin when the voltage fluctuates. The power supply is 3 power supply lines. Do not connect the positive and negative poles of the power supply to avoid burning. Bad board
2. Power supply is recommended for DC dual power supply ±75V filter better power supply
3. Speaker recommended 10-25 inch 2 ohm-8 ohm speaker
4. Although the audio output has short circuit protection, try not to short circuit.
5. Please check carefully before powering on, to ensure that the wiring is correct before power can be applied.
7. The voltage amplification factor of this board is fixed at 40 times. If the output power is not enough, add the preamplifier according to the specific situation.
 
The parameters are as follows:
 
1. Power supply voltage: dual DC power supply ±58---±80V
2. Maximum rated output power: ±70V power supply bridge mono mode: 2000W (4 ohm load)
 
                                                                        1200W (8 ohm load)
 
                                ±70V power supply bridge stereo mode: 2X700W (4 ohm load)
 
                                                                        2X350W (8 ohm load)
3. Efficiency: >=90%
4. Signal to noise ratio: 90dB
5. Total harmonic distortion: 2000W (±70 power supply 4 ohm bridge mode, distortion <1%)
500W (±85 power supply 8 ohm speakers, distortion <1%)
6. Frequency response range: 20Hz-22KHz
7. Voltage amplification: 45 times
 
8. Static power consumption: 8W
 
9. Input sensitivity 1.1V (RMS)
10. Output short circuit protection: Yes
11. Output DC bias protection is speaker protection: Yes
12. Over-temperature protection: Yes, the temperature of the radiator FET is higher than 100 °C, and the output is turned off!
13. Power amplifier board size: length x width x height = 135x132x45mm
14. Weight: 550 g
 
If it is not the power supply of the switching power supply, it is necessary to add the rectifier filter circuit by the power supply of the ring cattle!
 
If your switching power supply is not a dual output but a single output, you need two single power supplies in series.
 
This board is a full-frequency pure final stage power amplifier. It needs to be used as a subwoofer to add a pre-stage low-pass filter.
 
The board is powered by dual DC voltage. The car battery cannot be used as a single power supply. It needs to be powered by a car amplifier.
 
Power supply:
 
https://www.aliexpress.com/store/product/Lusya-AC200V-240V-LLC-Switching-Power-Supply-Board-800W-Output-voltage-50V-For-Amplifier-board/314284_32907753578.html?spm=2114.12010612.8148356.18.21d3afa4BmuRwO

Package:

1 x   2000W HIFI power Amplifier board   

11

 

DSC_0137DSC_0136DSC_0131DSC_0133

IMG_2774(20190610-172358)IMG_2771O1CN01g15sQc1bEMCajdAIe_!!161633433 (1)O1CN01UDp49h1bEMCdK87uj_!!161633433 (1)O1CN01UUpMGc1bEMCbaFlwF_!!161633433O1CN01vx6aiF1bEMCaje2MJ_!!161633433 (1)

  • Shipping

    We offer discounted shipping rates which can be calculated during checkout

  • Returns

    You may return an item in new condition with no questions asked for 13 days after confirmed delivery.